Strict Bodyweight Pull-Up vs Single Arm Cable High Row

Strict Bodyweight Pull-Up vs Single Arm Cable High Row Strength Standards

The men’s and women’s tables show the exact Novice-through-Elite targets for both exercises. Weight-based targets use bodyweight and display actual pounds and kilograms. Repetition and time standards keep their exercise-specific units and use age only when the individual exercise standards require it.

Age and bodyweight are never combined as row dimensions. Internal bodyweight-ratio scores are never displayed. When the exercises use unlike measurements, the table presents an explicit reference crosswalk instead of inventing a conversion.

Men’s Strict Bodyweight Pull-Up vs Single Arm Cable High Row Standards

Reference crosswalk: Unlike measurements are not subtracted or converted. Each column states its own reference and preserves the exercise’s real unit.

Women’s Strict Bodyweight Pull-Up vs Single Arm Cable High Row Standards

Reference crosswalk: Unlike measurements are not subtracted or converted. Each column states its own reference and preserves the exercise’s real unit.

How Your Strict Bodyweight Pull-Up vs Single Arm Cable High Row Result Is Calculated

The two exercises can use different measurements. The calculator rates each result against the standards for that exercise first, then compares the resulting strength levels and progress toward the next level. It never invents a reps-to-weight conversion.

1. Estimate the weight-based result

For Single Arm Cable High Row, one rep uses the weight entered. For 2–12 reps, the calculator runs both estimates and keeps the lower result.

• Epley: weight × (1 + reps ÷ 30)
• Brzycki: weight × 36 ÷ (37 − reps)

For a useful Strict Bodyweight Pull-Up vs Single Arm Cable High Row comparison, use clean, recent sets performed with consistent technique and range of motion. Lower-rep sets usually require less extrapolation.

2. Rate the Strict Bodyweight Pull-Up result

The exercise-specific tool supplies sex-, bodyweight-band-, and age-specific repetition thresholds plus a stretch target. The calculator uses strict continuous bodyweight repetitions and does not convert the repetitions into an estimated weight.

3. Rate the Single Arm Cable High Row result

The standards use the sex-specific thresholds from the individual Single Arm Cable High Row tool. The target adjusts to bodyweight using reference target × (user bodyweight ÷ reference bodyweight) to the two-thirds power.

4. Compare strength level and progress

The lower strength level is the priority. When both exercises reach the same level, a priority appears only when one is at least 10 points farther from its next target. Otherwise, the result is Balanced. Age range changes only the exercise whose standards include age; it remains an analytics field for the other exercise.

How Men’s Strict Bodyweight Pull-Up and Single Arm Cable High Row Standards Differ

The line chart below preserves each exercise’s real standards measurement in its own panel. Repetitions, seconds, and weights are never converted into one another.

How Women’s Strict Bodyweight Pull-Up and Single Arm Cable High Row Standards Differ

The line chart below preserves each exercise’s real standards measurement in its own panel. Repetitions, seconds, and weights are never converted into one another.

Strict Bodyweight Pull-Up and Single Arm Cable High Row Exercises Used by This Calculator

Valid results depend on using the specified strict bodyweight pull-up and single arm cable high row technique and load convention. Use strict, repeatable Strict Bodyweight Pull-Up and Single Arm Cable High Row tests that follow each exercise’s setup, range of motion, equipment, and load rules. Do not mix variations, assistance, partial range, momentum, or different load conventions.

Use the Strict Bodyweight Pull-Up setup and load convention

Strict, unbroken set of dead-hang pull-ups. Pronated grip with chin clearly above the bar at the top. No kipping, hip drive, or leg swing. Full arm extension at the bottom of each rep. One continuous set with no rest.

Use the Single Arm Cable High Row setup and load convention

Entered load is the selected or loaded cable resistance for the one working handle and one arm at a time. Do not enter bodyweight, combined left-plus-right load, another station’s converted force, or a different implement’s load. Reps are total valid reps across both arms combined, using the same strict high-row standard on each side. No side selector, separate left/right entries, or imbalance score is supported; this tool scores the total-combined unilateral test only. Consistent setup, range, and finish quality across the entered set. No substituted exercise or assisted reps.

Enter one recent Strict Bodyweight Pull-Up result and one recent Single Arm Cable High Row result

First exercise: Strict continuous Strict Bodyweight Pull-Up reps. Second exercise: Total external load and a whole number from 1 to 12 reps. Use the units shown.

Related Tools

• Strict Bodyweight Pull-Up — View the individual Strict Bodyweight Pull-Up standards and next strength-level target.
• Single Arm Cable High Row — View the individual Single Arm Cable High Row standards and next strength-level target.
• One Arm Lat Pulldown — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.
• Standing Cable Row — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.
• Cable High Row — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.
• Face Pull — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.