Barbell Side Lunge vs Safety Bar Hatfield Squat

Barbell Side Lunge vs Safety Bar Hatfield Squat Strength Standards

Use these tables to compare the estimated one-rep max required for the barbell side lunge and safety bar hatfield squat to reach the same strength level at each listed bodyweight. The numbers are calculator targets, not a required gap between the two lifts.

Choose the men’s or women’s table, find the closest bodyweight row, and read across to Novice, Intermediate, Advanced, or Elite. Each entry shows Barbell Side Lunge / Safety Bar Hatfield Squat, with pounds above kilograms. Use the calculator for your exact bodyweight and recent sets.

Men’s Barbell Side Lunge vs Safety Bar Hatfield Squat Standards

How to read the table: Find the closest bodyweight, then use the labeled exercise row. Every strength-level entry shows one target with pounds first and kilograms beneath it.

Women’s Barbell Side Lunge vs Safety Bar Hatfield Squat Standards

How to read the table: Find the closest bodyweight, then use the labeled exercise row. Every strength-level entry shows one target with pounds first and kilograms beneath it.

How Your Barbell Side Lunge vs Safety Bar Hatfield Squat Result Is Calculated

The calculator estimates both one-rep maxes, rates each one against its exercise and bodyweight standards, and then compares the two ratings.

1. Estimate a one-rep max from each set

A one-rep set uses the entered weight. For 2–12 reps, both formulas are calculated and the lower estimate is retained.

• Epley: weight × (1 + reps ÷ 30)
• Brzycki: weight × 36 ÷ (37 − reps)

For the most useful Barbell Side Lunge vs Safety Bar Hatfield Squat comparison, enter clean, difficult sets performed with the same technique and range of motion you use in training. Lower-rep sets usually require less extrapolation.

2. Find the barbell side lunge strength level

For barbell side lunge, the individual exercise thresholds start from reference bodyweights of 190 lb for men and 150 lb for women. Exact-bodyweight targets use reference target × (user bodyweight ÷ reference bodyweight) to the two-thirds power.

The target rises more slowly than bodyweight so larger lifters are expected to lift more without requiring strength to increase pound for pound.

3. Find the safety bar hatfield squat strength level

The safety bar hatfield squat rating uses its sex-specific exercise standards. Reference targets at 190 lb for men and 150 lb for women are scaled to the entered bodyweight by reference target × (user bodyweight ÷ reference bodyweight) to the two-thirds power.

The target rises more slowly than bodyweight so larger lifters are expected to lift more without requiring strength to increase pound for pound.

4. Compare the two results

The lift with the lower Beginner-to-Elite rating is the priority. If both ratings match, the calculator requires a 10-point difference in next-level progress before naming a priority; otherwise it reports Balanced.

The result identifies the lower standards rating, not its cause. Technique, fatigue, training history, and set quality can all affect the comparison. Age range is recorded anonymously but does not change these standards.

Enter both sets above to see the estimated maxes, assigned levels, next-level targets, and comparison result.

How Men’s Barbell Side Lunge and Safety Bar Hatfield Squat Standards Differ

How to read this chart: Choose a strength level and follow its line across bodyweight. Values show the Safety Bar Hatfield Squat standard minus the Barbell Side Lunge standard: zero means equal, above zero means the Safety Bar Hatfield Squat standard is higher, and below zero means the Barbell Side Lunge standard is higher. Swipe horizontally on mobile. Use the standards table for exact lb/kg targets.

How Women’s Barbell Side Lunge and Safety Bar Hatfield Squat Standards Differ

How to read this chart: Choose a strength level and follow its line across bodyweight. Values show the Safety Bar Hatfield Squat standard minus the Barbell Side Lunge standard: zero means equal, above zero means the Safety Bar Hatfield Squat standard is higher, and below zero means the Barbell Side Lunge standard is higher. Swipe horizontally on mobile. Use the standards table for exact lb/kg targets.

Barbell Side Lunge and Safety Bar Hatfield Squat Exercises Used by This Calculator

The calculator expects repeatable barbell side lunge and safety bar hatfield squat results. Follow each exercise definition below so the two ratings are based on valid tests. Use strict, repeatable Barbell Side Lunge and Safety Bar Hatfield Squat tests that follow each exercise’s setup, range of motion, equipment, and load rules. Do not mix variations, assistance, partial range, momentum, or different load conventions.

Use the exercise-specific Barbell Side Lunge setup and load convention

Barbell is positioned on the upper back; high-bar or low-bar placement is allowed. Lifter begins standing upright with feet hip-width apart. Lifter steps laterally into a wide stance. Working foot remains flat and planted throughout the rep. Lifter descends by sitting into the working hip. Non-working leg remains extended with minimal knee bend. Working thigh reaches at least parallel, with hip crease at or below knee level. Each repetition counts only after returning to a fully upright standing position with hips and knees extended and feet returned under the body. Torso remains neutral with minimal forward collapse or rotation. Each rep is controlled with consistent depth, step width, and tempo. Reps are performed evenly on both sides; weaker side determines valid load and rep count. Raw lifting only; no equipped or assisted support is included. No shallow side steps without clear depth, forward or rotational lunge substitutions, excessive torso lean, momentum-assisted returns, assisted variations, machine-based lateral lunges, Smith machine variations, partial reps, uneven step widths, or equipped lifting are included. Load input represents total barbell weight only, not bodyweight. Standards reflect unilateral lower-body strength with significant lateral stability demands. Side lunges typically allow less loading than forward or reverse lunges due to reduced mechanical efficiency. Most lifters are limited by hip mobility, adductor strength, and lateral balance. Shallow depth or shortened step width will inflate results. Strict, repeatable execution is required for valid comparisons. Estimated 1RM is calculated from the entered weight used and reps.

Use the Safety Bar Hatfield Squat setup and load convention

The total loaded safety squat bar weight, including the actual bar weight and all plates, squatted with fixed hand supports used only for balance. Supported safety-bar Hatfield squat reps. Squat the loaded safety bar to valid depth while using the fixed hand supports for balance only, then stand to full lockout without pulling the body through the hardest part. Consistent setup, range, and finish quality across the entered set. No substituted exercise or assisted reps.

Enter one recent Barbell Side Lunge result and one recent Safety Bar Hatfield Squat result

First lift: weight used and 1–12 strict reps. Second lift: weight used and 1–12 strict reps. Pounds or kilograms.

Related Tools

• Barbell Side Lunge — View the individual Barbell Side Lunge standards and next strength-level target.
• Safety Bar Hatfield Squat — View the individual Safety Bar Hatfield Squat standards and next strength-level target.
• Barbell Cossack Squat — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.
• Barbell Lunge — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.
• Safety Bar Squat — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.
• Paused Front Squat — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.