Barbell Side Lunge vs Farmer’s Handle Deadlift

Barbell Side Lunge vs Farmer’s Handle Deadlift Strength Standards

Use these tables to compare the estimated one-rep max required for the barbell side lunge and farmer’s handle deadlift to reach the same strength level at each listed bodyweight. The numbers are calculator targets, not a required gap between the two lifts.

Choose the men’s or women’s table, find the closest bodyweight row, and read across to Novice, Intermediate, Advanced, or Elite. Each entry shows Barbell Side Lunge / Farmer’s Handle Deadlift, with pounds above kilograms. Use the calculator for your exact bodyweight and recent sets.

Men’s Barbell Side Lunge vs Farmer’s Handle Deadlift Standards

How to read the table: Find the closest bodyweight, then use the labeled exercise row. Every strength-level entry shows one target with pounds first and kilograms beneath it.

Women’s Barbell Side Lunge vs Farmer’s Handle Deadlift Standards

How to read the table: Find the closest bodyweight, then use the labeled exercise row. Every strength-level entry shows one target with pounds first and kilograms beneath it.

How Your Barbell Side Lunge vs Farmer’s Handle Deadlift Result Is Calculated

Both lifts are scored independently first: estimated max, bodyweight-adjusted strength level, and progress toward the next level. Those ratings drive the comparison.

1. Estimate a one-rep max from each set

The entered weight is used directly for one rep. With 2–12 reps, both estimates are compared and the lower value is used.

• Epley: weight × (1 + reps ÷ 30)
• Brzycki: weight × 36 ÷ (37 − reps)

Set quality matters for this Barbell Side Lunge vs Farmer’s Handle Deadlift comparison. Enter technically consistent, challenging sets, and prefer lower-rep results when practical because the estimate extends less far beyond the performed set.

2. Find the barbell side lunge strength level

The standards use the sex-specific thresholds from the individual Barbell Side Lunge tool. Targets begin at 190 lb for men and 150 lb for women, then adjust to exact bodyweight with reference target × (user bodyweight ÷ reference bodyweight) to the two-thirds power.

Two-thirds scaling raises the target as bodyweight rises while limiting the size advantage that a direct one-to-one adjustment would create.

3. Find the farmer’s handle deadlift strength level

The farmer’s handle deadlift rating uses its sex-specific exercise standards. Reference targets at 190 lb for men and 150 lb for women are scaled to the entered bodyweight by reference target × (user bodyweight ÷ reference bodyweight) to the two-thirds power.

The target rises more slowly than bodyweight so larger lifters are expected to lift more without requiring strength to increase pound for pound.

4. Compare the two results

Each max receives a level from Beginner through Elite. The lower-level lift becomes the priority. At matching levels, a priority appears only when one lift is at least 10 points farther from its next level; otherwise the result is Balanced.

Treat the result as a training comparison rather than an explanation of why one lift trails. Set quality, fatigue, skill, and training exposure all matter. Age range is recorded anonymously but does not change these standards.

Enter both sets above to see the estimated maxes, assigned levels, next-level targets, and comparison result.

How Men’s Barbell Side Lunge and Farmer’s Handle Deadlift Standards Differ

How to read this chart: Choose a strength level and follow its line across bodyweight. Values show the Farmer’s Handle Deadlift standard minus the Barbell Side Lunge standard: zero means equal, above zero means the Farmer’s Handle Deadlift standard is higher, and below zero means the Barbell Side Lunge standard is higher. Swipe horizontally on mobile. Use the standards table for exact lb/kg targets.

How Women’s Barbell Side Lunge and Farmer’s Handle Deadlift Standards Differ

How to read this chart: Choose a strength level and follow its line across bodyweight. Values show the Farmer’s Handle Deadlift standard minus the Barbell Side Lunge standard: zero means equal, above zero means the Farmer’s Handle Deadlift standard is higher, and below zero means the Barbell Side Lunge standard is higher. Swipe horizontally on mobile. Use the standards table for exact lb/kg targets.

Barbell Side Lunge and Farmer’s Handle Deadlift Exercises Used by This Calculator

The calculator expects repeatable barbell side lunge and farmer’s handle deadlift results. Follow each exercise definition below so the two ratings are based on valid tests. Use strict, repeatable Barbell Side Lunge and Farmer’s Handle Deadlift tests that follow each exercise’s setup, range of motion, equipment, and load rules. Do not mix variations, assistance, partial range, momentum, or different load conventions.

Use the exercise-specific Barbell Side Lunge setup and load convention

Barbell is positioned on the upper back; high-bar or low-bar placement is allowed. Lifter begins standing upright with feet hip-width apart. Lifter steps laterally into a wide stance. Working foot remains flat and planted throughout the rep. Lifter descends by sitting into the working hip. Non-working leg remains extended with minimal knee bend. Working thigh reaches at least parallel, with hip crease at or below knee level. Each repetition counts only after returning to a fully upright standing position with hips and knees extended and feet returned under the body. Torso remains neutral with minimal forward collapse or rotation. Each rep is controlled with consistent depth, step width, and tempo. Reps are performed evenly on both sides; weaker side determines valid load and rep count. Raw lifting only; no equipped or assisted support is included. No shallow side steps without clear depth, forward or rotational lunge substitutions, excessive torso lean, momentum-assisted returns, assisted variations, machine-based lateral lunges, Smith machine variations, partial reps, uneven step widths, or equipped lifting are included. Load input represents total barbell weight only, not bodyweight. Standards reflect unilateral lower-body strength with significant lateral stability demands. Side lunges typically allow less loading than forward or reverse lunges due to reduced mechanical efficiency. Most lifters are limited by hip mobility, adductor strength, and lateral balance. Shallow depth or shortened step width will inflate results. Strict, repeatable execution is required for valid comparisons. Estimated 1RM is calculated from the entered weight used and reps.

Use the Farmer’s Handle Deadlift setup and load convention

The total combined farmer-handle weight pulled from the floor. Raw farmer’s handle deadlift reps. Pull two matched farmer’s handles from a dead-stop floor start to full standing lockout with raw grip and controlled handles, without straps, hitching, thigh ramping, rack starts, raised handles, static holds, or carry steps. Consistent setup, range, and finish quality across the entered set. No substituted exercise or assisted reps.

Enter one recent Barbell Side Lunge result and one recent Farmer’s Handle Deadlift result

First lift: weight used and 1–12 strict reps. Second lift: weight used and 1–12 strict reps. Pounds or kilograms.

Related Tools

• Barbell Side Lunge — View the individual Barbell Side Lunge standards and next strength-level target.
• Farmer’s Handle Deadlift — View the individual Farmer’s Handle Deadlift standards and next strength-level target.
• Barbell Cossack Squat — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.
• Barbell Lunge — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.
• Trap Bar Deadlift — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.
• Barbell Rack Pull — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.