Barbell Bent-Over Row vs Wide Grip Pull Ups Strength Standards

Bent Over Row vs Wide Grip Pull Ups Strength Standards

The men’s and women’s tables show the exact Novice-through-Elite targets for both exercises. Weight-based targets use bodyweight and display actual pounds and kilograms. Repetition and time standards keep their exercise-specific units and use age only when the individual exercise standards require it.

Age and bodyweight are never combined as row dimensions. Internal bodyweight-ratio scores are never displayed. When the exercises use unlike measurements, the table presents an explicit reference crosswalk instead of inventing a conversion.

Men’s Bent-Over Row vs Wide Grip Pull Ups Standards

Reference crosswalk: Unlike measurements are not subtracted or converted. Each column states its own reference and preserves the exercise’s real unit.

Women’s Bent-Over Row vs Wide Grip Pull Ups Standards

Reference crosswalk: Unlike measurements are not subtracted or converted. Each column states its own reference and preserves the exercise’s real unit.

How Your Bent Over Row vs Wide Grip Pull Ups Result Is Calculated

The two exercises can use different measurements. The calculator rates each result against the standards for that exercise first, then compares the resulting strength levels and progress toward the next level. It never invents a reps-to-weight conversion.

1. Estimate the weight-based result

For Bent-Over Row, one rep uses the weight entered. For 2–12 reps, the calculator runs both estimates and keeps the lower result.

• Epley: weight × (1 + reps ÷ 30)
• Brzycki: weight × 36 ÷ (37 − reps)

For a useful Bent Over Row vs Wide Grip Pull Ups comparison, use clean, recent sets performed with consistent technique and range of motion. Lower-rep sets usually require less extrapolation.

2. Rate the Bent-Over Row result

The standards use the sex-specific total-barbell thresholds from the individual tool. The target adjusts to bodyweight using reference target × (user bodyweight ÷ reference bodyweight) to the two-thirds power.

3. Rate the Wide Grip Pull Ups result

The exercise-specific tool supplies sex-, bodyweight-band-, and age-specific repetition thresholds plus a stretch target. The calculator uses strict continuous bodyweight repetitions and does not convert the repetitions into an estimated weight.

4. Compare strength level and progress

The lower strength level is the priority. When both exercises reach the same level, a priority appears only when one is at least 10 points farther from its next target. Otherwise, the result is Balanced. Age range changes only the exercise whose standards include age; it remains an analytics field for the other exercise.

How Men’s Bent Over Row and Wide Grip Pull Ups Standards Differ

The line chart below preserves each exercise’s real standards measurement in its own panel. Repetitions, seconds, and weights are never converted into one another.

How Women’s Bent Over Row and Wide Grip Pull Ups Standards Differ

The line chart below preserves each exercise’s real standards measurement in its own panel. Repetitions, seconds, and weights are never converted into one another.

Bent Over Row and Wide Grip Pull Ups Exercises Used by This Calculator

Valid results depend on using the specified barbell bent-over row and wide grip pull ups technique and load convention. Use strict, repeatable Bent Over Row and Wide Grip Pull Ups tests that follow each exercise’s setup, range of motion, equipment, and load rules. Do not mix variations, assistance, partial range, momentum, or different load conventions.

Use the Barbell Bent-Over Row setup and load convention

Barbell starts from a dead hang below the shoulders. Torso is hinged forward and remains roughly near-parallel to the floor. Knees are slightly bent, hips are hinged, and the spine stays neutral. Bar is pulled to the lower ribs or upper abdomen each rep. Arms extend fully at the bottom of each rep. No torso heaving, hip snap, or body English. Consistent torso angle and bar path are required across tests. No Pendlay rows, Yates rows, cheat rows, T-bar rows, Smith machine rows, machine rows, partial range variants, or equipped lifting standards. Estimated 1RM is calculated from the entered load and reps.

Use the Wide Grip Pull Ups setup and load convention

Start from a controlled dead hang with a pronated grip wider than shoulder width, pull until the chin clearly passes above the bar, and return to full elbow extension. Stop when the rep no longer matches this test: standard-width pull-ups, close-grip pull-ups, chin-ups, neutral-grip reps, or any shortcut that changes the score. Do not count standard-width pull-ups, close-grip pull-ups, chin-ups, neutral-grip reps, kipping reps. Do not combine multiple sets into one score. Use the same setup, range rule, and rep-counting convention for retests.

Enter one recent Bent Over Row result and one recent Wide Grip Pull Ups result

First exercise: Total barbell weight and a whole number from 1 to 12 reps. Second exercise: Strict continuous Wide Grip Pull Ups reps. Use the units shown.

Related Tools

• Barbell Bent-Over Row — View the individual Bent-Over Row standards and next strength-level target.
• Wide Grip Pull Ups Strength Standards — View the individual Wide Grip Pull Ups standards and next strength-level target.
• Inverted Row Strength Standards — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.
• Lat Pulldown (Strict) — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.
• Close Grip Lat Pulldown — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.
• Reverse Grip Lat Pulldown — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.