Barbell Side Lunge vs Barbell Push Press

Barbell Side Lunge vs Push Press Strength Standards

The paired standards below show what the barbell side lunge and push press each require at the same strength level. They are separate exercise targets rather than a prescribed difference between your lifts.

Select the appropriate sex table and nearest bodyweight, then choose a strength-level column. Values are ordered Barbell Side Lunge / Push Press in pounds with kilograms underneath. The calculator above handles exact bodyweight and set inputs.

Men’s Barbell Side Lunge vs Push Press Standards

How to read the table: Find the closest bodyweight, then use the labeled exercise row. Every strength-level entry shows one target with pounds first and kilograms beneath it.

Women’s Barbell Side Lunge vs Push Press Standards

How to read the table: Find the closest bodyweight, then use the labeled exercise row. Every strength-level entry shows one target with pounds first and kilograms beneath it.

How Your Barbell Side Lunge vs Push Press Result Is Calculated

Each set is converted to an estimated max before the calculator assigns exercise-specific strength levels and compares them.

1. Estimate a one-rep max from each set

When the set contains one rep, the entered load is the estimate. For 2–12 reps, the calculator keeps the less aggressive of the two formula results.

• Epley: weight × (1 + reps ÷ 30)
• Brzycki: weight × 36 ÷ (37 − reps)

For the most useful Barbell Side Lunge vs Push Press comparison, enter clean, difficult sets performed with the same technique and range of motion you use in training. Lower-rep sets usually require less extrapolation.

2. Find the barbell side lunge strength level

The standards use the sex-specific thresholds from the individual Barbell Side Lunge tool. Targets begin at 190 lb for men and 150 lb for women, then adjust to exact bodyweight with reference target × (user bodyweight ÷ reference bodyweight) to the two-thirds power.

This adjustment expects larger lifters to move more weight, but it does not increase the target pound for pound with bodyweight.

3. Find the push press strength level

For push press, the individual exercise thresholds start from reference bodyweights of 190 lb for men and 150 lb for women. Exact-bodyweight targets use reference target × (user bodyweight ÷ reference bodyweight) to the two-thirds power.

This adjustment expects larger lifters to move more weight, but it does not increase the target pound for pound with bodyweight.

4. Compare the two results

Strength level decides the comparison first. Matching levels remain Balanced unless progress toward the next target differs by at least 10 points.

A priority result is a standards comparison, not a diagnosis. Differences in technique, fatigue, practice, or set effort may influence it. Age range is recorded anonymously and does not alter these standards.

Use the calculator above to view both estimated maxes, strength levels, next targets, and the resulting priority or Balanced verdict.

How Men’s Barbell Side Lunge and Push Press Standards Differ

How to read this chart: Choose a strength level and follow its line across bodyweight. Values show the Push Press standard minus the Barbell Side Lunge standard: zero means equal, above zero means the Push Press standard is higher, and below zero means the Barbell Side Lunge standard is higher. Swipe horizontally on mobile. Use the standards table for exact lb/kg targets.

How Women’s Barbell Side Lunge and Push Press Standards Differ

How to read this chart: Choose a strength level and follow its line across bodyweight. Values show the Push Press standard minus the Barbell Side Lunge standard: zero means equal, above zero means the Push Press standard is higher, and below zero means the Barbell Side Lunge standard is higher. Swipe horizontally on mobile. Use the standards table for exact lb/kg targets.

Barbell Side Lunge and Push Press Exercises Used by This Calculator

The calculator expects repeatable barbell side lunge and push press results. Follow each exercise definition below so the two ratings are based on valid tests. Use strict, repeatable Barbell Side Lunge and Push Press tests that follow each exercise’s setup, range of motion, equipment, and load rules. Do not mix variations, assistance, partial range, momentum, or different load conventions.

Use the exercise-specific Barbell Side Lunge setup and load convention

Barbell is positioned on the upper back; high-bar or low-bar placement is allowed. Lifter begins standing upright with feet hip-width apart. Lifter steps laterally into a wide stance. Working foot remains flat and planted throughout the rep. Lifter descends by sitting into the working hip. Non-working leg remains extended with minimal knee bend. Working thigh reaches at least parallel, with hip crease at or below knee level. Each repetition counts only after returning to a fully upright standing position with hips and knees extended and feet returned under the body. Torso remains neutral with minimal forward collapse or rotation. Each rep is controlled with consistent depth, step width, and tempo. Reps are performed evenly on both sides; weaker side determines valid load and rep count. Raw lifting only; no equipped or assisted support is included. No shallow side steps without clear depth, forward or rotational lunge substitutions, excessive torso lean, momentum-assisted returns, assisted variations, machine-based lateral lunges, Smith machine variations, partial reps, uneven step widths, or equipped lifting are included. Load input represents total barbell weight only, not bodyweight. Standards reflect unilateral lower-body strength with significant lateral stability demands. Side lunges typically allow less loading than forward or reverse lunges due to reduced mechanical efficiency. Most lifters are limited by hip mobility, adductor strength, and lateral balance. Shallow depth or shortened step width will inflate results. Strict, repeatable execution is required for valid comparisons. Estimated 1RM is calculated from the entered weight used and reps.

Use the exercise-specific Push Press setup and load convention

Barbell starts in the front rack position at the shoulders. A controlled dip is performed using the legs and hips before driving the bar upward. Leg drive initiates the bar path and the arms finish the lockout overhead. Each rep counts only when the bar is fully locked out overhead with elbows fully extended. The bar must remain under control throughout the full range of motion. Dip depth and technique must stay consistent across tests. Raw lifting only. Allowed equipment: barbell, rack, belt (optional), wrist wraps (optional), lifting shoes (optional). Excluded variations: strict overhead press (no leg drive), push jerk, split jerk, partial lockout reps, Smith machine pressing, and machine shoulder press variations. Estimated 1RM is calculated from the entered load and reps.

Enter one recent Barbell Side Lunge result and one recent Push Press result

First lift: weight used and 1–12 strict reps. Second lift: total barbell load and 1–12 strict reps. Pounds or kilograms.

Related Tools

• Barbell Side Lunge — View the individual Barbell Side Lunge standards and next strength-level target.
• Barbell Push Press — View the individual Push Press standards and next strength-level target.
• Barbell Cossack Squat — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.
• Barbell Lunge — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.
• Arnold Press — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.
• Barbell Clean And Jerk — Use this related standards tool to examine a closely related exercise without mixing its result into this comparison.